TorqHive

Crimped vs Soldered Terminals: What IEC 60352-2 Requires and Why Crimp Height Decides the Joint

Published: Nov 06, 2026 • Category: Material & Engineering • 10 min read

The joint nobody inspects until it fails

Crimping sits in an awkward place in most workshops: it is fast, it is cheap, and it is almost never checked. The questions on Reddit reflect that. In "Crimping wires help" the answer is a warning rather than a technique: "A real set of crimpers would be better but you'll survive, just make sure it has good contact metal to wire." In "Which Crimper do you recommend?" the argument is entirely about the tool, and in "What tool to use" it is about matching one specific terminal to one specific wire size.

All three threads are circling the same fact: the crimp is a system of three parts — terminal, die and wire — and the quality of the joint is set by how far the barrel is compressed, not by how hard the operator squeezes. That is a measurable quantity, which is what makes it specifiable.

What a crimp actually is

In a correct crimp, the barrel is compressed around the strands until the individual wires deform into each other and into the barrel. The result is a large, oxygen-excluded contact area with no voids, held by elastic springback rather than by friction. Done properly, the joint is mechanically stronger than the wire beside it and electrically indistinguishable from a continuous conductor. Done badly, it is a resistor with a mechanical joint attached, and it fails by heating.

IEC 60352-2 is the standard that frames this. The 2024 edition applies to solderless crimped connections made with appropriately designed uninsulated or pre-insulated crimp barrels, and the edition it supersedes covered stranded and solid conductors from 0.05 mm2 to 10 mm2. It sets general requirements, test methods and practical guidance — it does not tell you which tool to buy, and it does not certify a crimper. That gap is where product quality lives.

On the acceptance side, IPC/WHMA-A-620 is the reference most harness shops work to for cable and wire assembly, including crimped connections. A distributor selling into automotive, marine or industrial harness supply will be asked about both: IEC 60352-2 for the connection, IPC/WHMA-A-620 for the workmanship.

Crimp height is the process, pull force is the exam

Every terminal has a compression window. Below the lower limit the barrel is over-compressed: strands are cut, the barrel thins at the corners, and the joint can crack under vibration. Above the upper limit it is under-crimped: voids remain between strands, resistance rises, and the joint heats under load until the insulation discolours. Between the limits the joint is gas-tight and stable.

That window is why crimp height — measured with a crimp height gauge or a micrometer across the compressed barrel — is the production control, and pull force is the audit. Pull testing tells you whether the joint you already made is acceptable; crimp height is what keeps every joint in the batch inside the window. A shop that only pull-tests is inspecting a sample and hoping.

SymptomUsual causeWhat to change
Barrel cracked or wings touchingOver-crimped: wrong die for the terminal, or a die worn past its toleranceCorrect die cavity, replace worn die, set the crimp height stop
Strands pull out below loadUnder-crimped, or wire gauge above the terminal rangeVerify wire range against the terminal maker's table; adjust crimp height
Insulation pierced or cutInsulation crimp set as tight as the conductor crimpSeparate the two adjustments; the insulation crimp should grip, not bite
Joint heats in serviceVoids or oxide in the barrel, often from tinned or contaminated strandsClean strands, no solder pre-tinning, re-crimp with correct height
Terminal loose on the studCompression changed the barrel length and the terminal geometryCheck terminal orientation in the die; crimp before forming or bending

The ratchet is a process control, not a convenience

A ratcheting crimper will not release until the full cycle is complete. That single feature is the difference between a tool and a gauge. A simple plier-style crimper lets the operator stop when the joint looks closed, which on a 6 mm2 terminal is well before the barrel has actually compressed. The ratchet removes that judgement: either the cycle completes, or the tool stays locked on the terminal and the operator finishes the stroke.

This is why the mechanism matters more than the handle. A ratchet with a soft release, a worn pawl or a plastic body that flexes under load will complete the cycle without delivering the intended compression. On the 0.5 to 6 mm2 ratcheting crimper, the full-cycle release and the hardened colour-coded dies are the two features that carry the quality, not the grip.

Two cavities, two different jobs

An insulated terminal is crimped twice in one stroke. The conductor crimp compresses the barrel onto bare strands. The insulation crimp closes the rear section around the insulation to provide strain relief. They are separate adjustments and they must not be set the same.

  • Conductor crimp — full compression, barrel closed, a slight bell mouth at the wire entry so strands are not sheared at the edge.
  • Insulation crimp — grips the insulation without piercing it. A pierced insulation is a moisture path and a dielectric failure waiting for a damp environment.
  • Strip length — long enough that strands reach the end of the barrel, short enough that bare copper does not extend past it. Both errors are visible, and both are common.
  • Orientation — the seam of the barrel belongs opposite the die anvil. Crimping on the seam splits it.

Where solder wins, and where it does not

Solder is not obsolete, but it solves a different problem. A soldered joint is electrically excellent and easy to inspect visually. It is also stiff: solder wicks up the strands and creates a rigid section immediately behind a flexible one, which is a stress concentration under vibration. In a harness that flexes, that is where the conductor breaks — not at the terminal, but just behind it.

Crimping keeps the strands flexible up to the barrel. That is why automotive, aerospace and industrial harness standards are built around crimped connections and treat solder as a rework or repair method, not a production process. Solder also leaves flux residue that must be cleaned, and it makes a joint that cannot be re-terminated without cutting the wire back.

The exception worth naming: a soldered joint is often the better choice for a single, static, well-supported connection in a prototype or a repair where the correct terminal and die are not available. The mistake is treating that as a production method, then wondering why the harness fails at the 20,000-cycle vibration test.

Matching the die to the terminal

The colour code on pre-insulated terminals — red, blue, yellow — is a manufacturer convention for wire range, not an international specification, and the ranges behind the colours are not identical between brands. Two consequences follow. First, the terminal's own datasheet, not the colour, defines the wire range. Second, a die marked for one brand's insulated terminal may not be correct for another's, even at the same colour.

The safe purchasing rule is to buy terminal and die as a pair, or to require the terminal maker's crimp specification — wire range, strip length, crimp height and die reference — with the goods. A crimper sold without that data is a tool with no acceptance criteria, and no amount of operator skill fixes a missing specification.

What to specify on a private-label order

  • Wire range and standard reference. State the range in mm2 and AWG and reference IEC 60352-2 for the connection; add IPC/WHMA-A-620 if the customer is a harness builder.
  • Crimp height window. Ask for the nominal crimp height and tolerance per die cavity, and the gauge or method used to verify it.
  • Die material and hardness. Hardened dies hold the window; soft dies wear into under-crimping and nobody notices until returns appear.
  • Ratchet mechanism. Full-cycle release, serviceable pawl, and a release lever that does not defeat the ratchet in normal use.
  • Handle and insulation. For electrical work the grips must meet the relevant insulation standard; the VDE 1000 V marking is a specific claim with specific test requirements, and a red handle is not one.
  • Documentation. A crimp chart on the tool or in the box, and a spare-part path for dies. A crimper with no die availability is a disposable tool sold at a professional price.

The short version

  1. A crimp is controlled compression that produces a gas-tight, void-free joint. It is not a squeeze.
  2. IEC 60352-2 sets the requirements and tests; IPC/WHMA-A-620 sets workmanship acceptance for harness work.
  3. Crimp height controls the process. Pull force audits it. You need both, in that order.
  4. The ratchet exists to guarantee a complete cycle — treat it as a process control, not a feature.
  5. Match die to terminal by datasheet, not by colour, and require the crimp specification with the goods.